GUANGDONG RUIHUI INTELLIGENT TECHNOLOGY CO., LTD.
GUANGDONG RUIHUI INTELLIGENT TECHNOLOGY CO., LTD. AUTOMATION SOLUTIONS FOR ALL METAL FORMING STAMPINGS APPROACHING RUIHUI, NEW AUTOMATION TECHNOLOGY IS UPGRADED.
Add to Cart
1. According to the feeding direction requirement, determine the installation position of the NC feeder (mostly the left side of the punch)
2. Hang the punch positioning block of the NC feeder fixing plate on the workbench of the punching machine. Note that the center line of the fixing plate and the center line of the punching plate of the punching machine should be aligned, and then attack the four M14 threads on the punching table. The hexagonal M14 screw fixing plate locks the punching table.
3. Loosen the nut with the serial number 1. Lift the NC feeder to align the fixed plate. After determining the height, the screw with the serial number 2 is screwed to the appropriate position. Finally, the hexagonal M14 screw and the M14 spring pad feeder are fixed on the punching table. Side of the plate.
4. During the installation process, if the horizontal position of the feeding height of the NC feeder is not consistent with the stamping height of the die, the NC feeder slide will have an adjustment of about 100 mm for adjustment.
5. When installing the mold on the press, make sure that the side of the mold is perpendicular to the direction of the roller of the NC feeder.
6. according to customer needs, install the electric control box and proximity switch in the appropriate part of the press, and check whether its operation is normal.
7. If there is anti-rust oil on the NC feeder, please be sure to remove it and add lubricant to the oil filling part.
8. Please refer to the electrical circuit diagram assembly for the power supply line of this unit.
9. Special attention: The NC feeder must be grounded to avoid electric shock events and circuits to prevent interference.
Specification:
| Model | MAC2-400 | MAC2-500 | MAC2-600 | MAC2-800 | ||
| Stock Width(mm) | 50-400 | 50-500 | 50-600 | 50-800 | ||
| Stock Thickness(mm) | 0.3~3.2 | 0.3-3.2 | 0.3-3.2 | -3.2 | ||
| Max.Coil Weight(kg) | 3000 | 3000 | 3000 | 5000 | 5000 | 7000 |
| Max.Coil O.D.(mm) | 1200 | 1200 | 1200 | |||
| Coil I.D.(mm) | 8 | 8 | 508 | 508 | ||
| Feed Length(mm) | ~500* | ~500* | ~500* | ~500* | ||
| Max. Line Speed(m/min) | 16-24 | 16-24 | 16-24 | 16-24 | ||
| Work Roll Number(pieces) | upper 6 lower 5 | upper 6 lower 5 | upper 6 lower 5 | upper 6 lower 5 | ||
| Feed Roll Number(set) | 1 | 1 | 1 | 1 | ||
| Main Motor(kw) | AC2.9 | AC2.9 | AC4.4 | AC4.4 | ||
| Mandrel Expansion | hydraulic | hydraulic | hydraulic | hydraulic | ||
| Reel Motor(kw) | 1.5 | 1.5 | 1.5 | 2.2 | 2.2 | 3.7 |
| Power(V) | 3 Phase 220V/380V/50HZ | |||||
| Operating Air(Mpa) | 0.49 | 0.49 | 0.49 | 0.49 | ||
Straigtening performance:
| tock Thicknees (mm) | Stock Width (mm) | |||
| 0.3 | 400 | 500 | 600 | 800 |
| 0.4 | ||||
| 0.6 | ||||
| 0.8 | ||||
| 1.0 | ||||
| 1.2 | ||||
| 1.4 | ||||
| 1.6 | 470 | 470 | ||
| 1.8 | 400 | 400 | ||
| 2.0 | 360 | 360 | ||
| 2.3 | 300 | 300 | 300 | 300 |
| 2.5 | 230 | 230 | 230 | 230 |
| 2.8 | 150 | 150 | 150 | 150 |
| 3.2 | 110 | 110 | 110 | 110 |
*1:(Pneumatic):Option in case of pneumatic mandrel expansion is provi
