GUANGDONG RUIHUI INTELLIGENT TECHNOLOGY CO., LTD.
GUANGDONG RUIHUI INTELLIGENT TECHNOLOGY CO., LTD. AUTOMATION SOLUTIONS FOR ALL METAL FORMING STAMPINGS APPROACHING RUIHUI, NEW AUTOMATION TECHNOLOGY IS UPGRADED.
Add to Cart
Uncoiler, Guangdong Steel Coil Unwinder, Ruihui Punch Automatic Feeder
1. Hydraulic pressing arm: The hydraulic pressing arm is rotated by the oil cylinder, so that the double pressing wheel is pressed on the outer surface of the sheet wrapped on the expansion and contraction drum of the heavy material frame, and then the gear reduction motor drives the double The pressure roller rotates to assist the sheet pulling during feeding to complete the automatic feeding.
2. Hydraulic feeding device: the supporting arm is hinged on the frame of Ruihui heavy-duty material frame, and is driven by the cylinder to rotate around the hinge point. The supporting surface of the hydraulic type feeding arm is curved, and the arc surface is installed. Guide wheel. When loading, the hydraulic pressure arm is rotated to the appropriate position by the oil cylinder, and the curved surface and the guide wheel structure can make the feeding material easier to be loaded into the expansion and contraction reel, and the hydraulic type feeding arm It is very convenient to load the material and the guide material.
3. Material arc photoelectric control device: The standard heavy-duty material frame adopts the contact type contact induction control mode. This control method is easy to scratch the material during contact, and the surface of the material must be conductive if it is to achieve the induction effect. For some materials with high surface degree requirements or materials that are not conductive, it is necessary to switch to photoelectric induction control, and use the arc photoelectric control to control the material. When the outer arc surface of the sheet enters the photoelectric range, the rack stops.
Specification:
| Model | MAC2-400 | MAC2-500 | MAC2-600 | MAC2-800 | ||
| Stock Width(mm) | 50-400 | 50-500 | 50-600 | 50-800 | ||
| Stock Thickness(mm) | 0.3~3.2 | 0.3-3.2 | 0.3-3.2 | -3.2 | ||
| Max.Coil Weight(kg) | 3000 | 3000 | 3000 | 5000 | 5000 | 7000 |
| Max.Coil O.D.(mm) | 1200 | 1200 | 1200 | |||
| Coil I.D.(mm) | 8 | 8 | 508 | 508 | ||
| Feed Length(mm) | ~500* | ~500* | ~500* | ~500* | ||
| Max. Line Speed(m/min) | 16-24 | 16-24 | 16-24 | 16-24 | ||
| Work Roll Number(pieces) | upper 6 lower 5 | upper 6 lower 5 | upper 6 lower 5 | upper 6 lower 5 | ||
| Feed Roll Number(set) | 1 | 1 | 1 | 1 | ||
| Main Motor(kw) | AC2.9 | AC2.9 | AC4.4 | AC4.4 | ||
| Mandrel Expansion | hydraulic | hydraulic | hydraulic | hydraulic | ||
| Reel Motor(kw) | 1.5 | 1.5 | 1.5 | 2.2 | 2.2 | 3.7 |
| Power(V) | 3 Phase 220V/380V/50HZ | |||||
| Operating Air(Mpa) | 0.49 | 0.49 | 0.49 | 0.49 | ||
Straigtening performance:
| tock Thicknees (mm) | Stock Width (mm) | |||
| 0.3 | 400 | 500 | 600 | 800 |
| 0.4 | ||||
| 0.6 | ||||
| 0.8 | ||||
| 1.0 | ||||
| 1.2 | ||||
| 1.4 | ||||
| 1.6 | 470 | 470 | ||
| 1.8 | 400 | 400 | ||
| 2.0 | 360 | 360 | ||
| 2.3 | 300 | 300 | 300 | 300 |
| 2.5 | 230 | 230 | 230 | 230 |
| 2.8 | 150 | 150 | 150 | 150 |
| 3.2 | 110 | 110 | 110 | 110 |
*1:(Pneumatic):Option in case of pneumatic mandrel expansion is provi