GUANGDONG RUIHUI INTELLIGENT TECHNOLOGY CO., LTD.
GUANGDONG RUIHUI INTELLIGENT TECHNOLOGY CO., LTD. AUTOMATION SOLUTIONS FOR ALL METAL FORMING STAMPINGS APPROACHING RUIHUI, NEW AUTOMATION TECHNOLOGY IS UPGRADED.
Add to Cart
Air feeder, sheet metal stamping, Dongguan Ruihui automatic roll feeder
At present, most of the punching and forming processes for rubber magnetic sheets are single-punching processes. The processing method is to first set the positioning pins on the punching mold, and then insert a piece of rubber magnetic sheet into the positioning pin, and the operator uses both hands. At the same time, press the punch start button to perform punching. After the punching is completed, the product is taken out from the mold, and another piece of rubber magnetic sheet is caught in the positioning groove or the positioning pin for the next punching.
Although the punching process can ensure the safety of personnel, the production efficiency is extremely low. Since the rubber magnetic sheet needs to be punched by a sheet shape, the proportion of the edge material is too large, and the input of the production cost is increased.
The air feeder presses and releases the floating rod through the reciprocating motion of the punching slider, so that the floating rod transmits the signal of pressing and releasing to the time relay and controls the driving device, thereby realizing continuous automatic feeding, thereby effectively Instead of pure manual feeding, it not only avoids the various drawbacks and unsafe factors of personnel operation, but also greatly reduces the labor intensity of operators.
The stamping production efficiency has been significantly improved. Since the automatic feeding by the air feeder can achieve accurate positioning and equidistant feeding, the production of the edge material can be reduced during the die cutting process, which not only improves the material utilization rate, but also improves the material utilization rate. It saves stamping production costs.
In actual use, the rubber magnetic sheet is first fed by the air feeder pallet, sequentially passes through the stopper wheel, the moving splint and the fixed clamping plate, and is placed on the work table on one side of the punch slider, so that the punch slider can punch it Cut; properly adjust the air feeder stopper wheel to position the rubber magnetic sheet.
Specification:
| Model | MAC2-400 | MAC2-500 | MAC2-600 | MAC2-800 | ||
| Stock Width(mm) | 50-400 | 50-500 | 50-600 | 50-800 | ||
| Stock Thickness(mm) | 0.3~3.2 | 0.3-3.2 | 0.3-3.2 | -3.2 | ||
| Max.Coil Weight(kg) | 3000 | 3000 | 3000 | 5000 | 5000 | 7000 |
| Max.Coil O.D.(mm) | 1200 | 1200 | 1200 | |||
| Coil I.D.(mm) | 8 | 8 | 508 | 508 | ||
| Feed Length(mm) | ~500* | ~500* | ~500* | ~500* | ||
| Max. Line Speed(m/min) | 16-24 | 16-24 | 16-24 | 16-24 | ||
| Work Roll Number(pieces) | upper 6 lower 5 | upper 6 lower 5 | upper 6 lower 5 | upper 6 lower 5 | ||
| Feed Roll Number(set) | 1 | 1 | 1 | 1 | ||
| Main Motor(kw) | AC2.9 | AC2.9 | AC4.4 | AC4.4 | ||
| Mandrel Expansion | hydraulic | hydraulic | hydraulic | hydraulic | ||
| Reel Motor(kw) | 1.5 | 1.5 | 1.5 | 2.2 | 2.2 | 3.7 |
| Power(V) | 3 Phase 220V/380V/50HZ | |||||
| Operating Air(Mpa) | 0.49 | 0.49 | 0.49 | 0.49 | ||
Straigtening performance:
| tock Thicknees (mm) | Stock Width (mm) | |||
| 0.3 | 400 | 500 | 600 | 800 |
| 0.4 | ||||
| 0.6 | ||||
| 0.8 | ||||
| 1.0 | ||||
| 1.2 | ||||
| 1.4 | ||||
| 1.6 | 470 | 470 | ||
| 1.8 | 400 | 400 | ||
| 2.0 | 360 | 360 | ||
| 2.3 | 300 | 300 | 300 | 300 |
| 2.5 | 230 | 230 | 230 | 230 |
| 2.8 | 150 | 150 | 150 | 150 |
| 3.2 | 110 | 110 | 110 | 110 |
*1:(Pneumatic):Option in case of pneumatic mandrel expansion is provi