GUANGDONG RUIHUI INTELLIGENT TECHNOLOGY CO., LTD.
GUANGDONG RUIHUI INTELLIGENT TECHNOLOGY CO., LTD. AUTOMATION SOLUTIONS FOR ALL METAL FORMING STAMPINGS APPROACHING RUIHUI, NEW AUTOMATION TECHNOLOGY IS UPGRADED.
Add to Cart
Gear feeder, cold rolled sheet stamping, Dongguan automatic feeder device
Adjusting the thickness of the material of the gear feeder: put the material into the roller by hand, turn the eccentric wheel to the position of 3 o'clock to adjust the loosening screw, so that the material can completely relax from the roller. Adjust the feeding thickness by the thickness adjustment screw, and pull it with the hand. material.
The material can be pulled back and forth without any resistance in the feeder. The clockwise rotation of the material thickness adjustment screw increases the apprenticeship, and the counterclockwise apprenticeship is small. If the test is appropriate, the highest point of the relaxation cam can be rotated backwards or forwards. By shaking the material by hand, you can feel the material starts to loosen.
If the resistance is very large, re-adjust the material thickness adjustment screw until it meets the requirements, but the gap should not be too large, which will cause the relaxation angle to be too large, which will affect the feeding accuracy.
Gear feeder relaxation angle adjustment:
1. Turn the eccentric wheel to the 3 o'clock position, that is, the feeding completion angle;
2. Turn the eccentric to the 4 o'clock position. At this time, the material is not fully pulled before and after.
3. Turn the eccentric wheel to the 5-6 o'clock position. At this time, the material is completely relaxed. Turn the eccentric wheel to the 7 to 8 o'clock position. At this time, the material is clamped. The feeding time is 9 o'clock and the feeding is started. The angle is exactly the same as the punching angle. Adjustment of the angle of relaxation of the entire feeder.
Specification:
| Model | MAC2-400 | MAC2-500 | MAC2-600 | MAC2-800 | ||
| Stock Width(mm) | 50-400 | 50-500 | 50-600 | 50-800 | ||
| Stock Thickness(mm) | 0.3~3.2 | 0.3-3.2 | 0.3-3.2 | -3.2 | ||
| Max.Coil Weight(kg) | 3000 | 3000 | 3000 | 5000 | 5000 | 7000 |
| Max.Coil O.D.(mm) | 1200 | 1200 | 1200 | |||
| Coil I.D.(mm) | 8 | 8 | 508 | 508 | ||
| Feed Length(mm) | ~500* | ~500* | ~500* | ~500* | ||
| Max. Line Speed(m/min) | 16-24 | 16-24 | 16-24 | 16-24 | ||
| Work Roll Number(pieces) | upper 6 lower 5 | upper 6 lower 5 | upper 6 lower 5 | upper 6 lower 5 | ||
| Feed Roll Number(set) | 1 | 1 | 1 | 1 | ||
| Main Motor(kw) | AC2.9 | AC2.9 | AC4.4 | AC4.4 | ||
| Mandrel Expansion | hydraulic | hydraulic | hydraulic | hydraulic | ||
| Reel Motor(kw) | 1.5 | 1.5 | 1.5 | 2.2 | 2.2 | 3.7 |
| Power(V) | 3 Phase 220V/380V/50HZ | |||||
| Operating Air(Mpa) | 0.49 | 0.49 | 0.49 | 0.49 | ||
Straigtening performance:
| tock Thicknees (mm) | Stock Width (mm) | |||
| 0.3 | 400 | 500 | 600 | 800 |
| 0.4 | ||||
| 0.6 | ||||
| 0.8 | ||||
| 1.0 | ||||
| 1.2 | ||||
| 1.4 | ||||
| 1.6 | 470 | 470 | ||
| 1.8 | 400 | 400 | ||
| 2.0 | 360 | 360 | ||
| 2.3 | 300 | 300 | 300 | 300 |
| 2.5 | 230 | 230 | 230 | 230 |
| 2.8 | 150 | 150 | 150 | 150 |
| 3.2 | 110 | 110 | 110 | 110 |
*1:(Pneumatic):Option in case of pneumatic mandrel expansion is provi