GUANGDONG RUIHUI INTELLIGENT TECHNOLOGY CO., LTD.
GUANGDONG RUIHUI INTELLIGENT TECHNOLOGY CO., LTD. AUTOMATION SOLUTIONS FOR ALL METAL FORMING STAMPINGS APPROACHING RUIHUI, NEW AUTOMATION TECHNOLOGY IS UPGRADED.
Add to Cart
Gear Feeder, Metal Deep Drawing, Guangdong Punch Automation Equipment
The installation of the gear feeder is divided into five major steps:
1. According to the requirements of the stamping process, determine the feeding direction and installation position of the gear feeder.
2. Determine the position of the center line on the side of the punching table of the gear feeder.
3. Align the center line of the mounting bottom plate of the gear feeder with the center line of the side of the punching table, drill the tapping on the punching machine body, and fix the feeder mounting plate on the punching bed. Pay special attention to the feeder. The centerline of the mounting plate matches the centerline of the punching table.
4. Fix the fuselage body of the gear feeder on the mounting plate. The fixing screws should not be tightened temporarily, and then adjust the height adjustment screw on the mounting plate according to the height of the center line of the mold.
Let the discharge center line of the feeder and the mold feed center line ensure the upper and lower and left and right absolute levels, and then lock the fixing screws between the mounting bottom plate and the feeder main body and the lock nut on the height adjusting screw.
The method of checking the level: start the punching machine, use the inching method to move the punching slider to the dead point, and release the gear feeder to release the cam. The purpose is to relax and not work, feed the material into the feeder, and synchronize with the hand. Pulley.
Feed the material into the mold to observe whether the material is smooth and without resistance in the mold. If there is resistance, jamming, etc., it indicates that it is not level, and it can be adjusted by adjusting the mold or the feeder.
5. Connect the gear feeder to the fixed output shaft of the punching machine. Adjust the length of the transmission belt to the appropriate position by adjusting the tension pulley. At this point, the entire installation process of the Ruihui gear feeder is completed.
Specification:
| Model | MAC2-400 | MAC2-500 | MAC2-600 | MAC2-800 | ||
| Stock Width(mm) | 50-400 | 50-500 | 50-600 | 50-800 | ||
| Stock Thickness(mm) | 0.3~3.2 | 0.3-3.2 | 0.3-3.2 | -3.2 | ||
| Max.Coil Weight(kg) | 3000 | 3000 | 3000 | 5000 | 5000 | 7000 |
| Max.Coil O.D.(mm) | 1200 | 1200 | 1200 | |||
| Coil I.D.(mm) | 8 | 8 | 508 | 508 | ||
| Feed Length(mm) | ~500* | ~500* | ~500* | ~500* | ||
| Max. Line Speed(m/min) | 16-24 | 16-24 | 16-24 | 16-24 | ||
| Work Roll Number(pieces) | upper 6 lower 5 | upper 6 lower 5 | upper 6 lower 5 | upper 6 lower 5 | ||
| Feed Roll Number(set) | 1 | 1 | 1 | 1 | ||
| Main Motor(kw) | AC2.9 | AC2.9 | AC4.4 | AC4.4 | ||
| Mandrel Expansion | hydraulic | hydraulic | hydraulic | hydraulic | ||
| Reel Motor(kw) | 1.5 | 1.5 | 1.5 | 2.2 | 2.2 | 3.7 |
| Power(V) | 3 Phase 220V/380V/50HZ | |||||
| Operating Air(Mpa) | 0.49 | 0.49 | 0.49 | 0.49 | ||
Straigtening performance:
| tock Thicknees (mm) | Stock Width (mm) | |||
| 0.3 | 400 | 500 | 600 | 800 |
| 0.4 | ||||
| 0.6 | ||||
| 0.8 | ||||
| 1.0 | ||||
| 1.2 | ||||
| 1.4 | ||||
| 1.6 | 470 | 470 | ||
| 1.8 | 400 | 400 | ||
| 2.0 | 360 | 360 | ||
| 2.3 | 300 | 300 | 300 | 300 |
| 2.5 | 230 | 230 | 230 | 230 |
| 2.8 | 150 | 150 | 150 | 150 |
| 3.2 | 110 | 110 | 110 | 110 |
*1:(Pneumatic):Option in case of pneumatic mandrel expansion is provi