GUANGDONG RUIHUI INTELLIGENT TECHNOLOGY CO., LTD.
GUANGDONG RUIHUI INTELLIGENT TECHNOLOGY CO., LTD. AUTOMATION SOLUTIONS FOR ALL METAL FORMING STAMPINGS APPROACHING RUIHUI, NEW AUTOMATION TECHNOLOGY IS UPGRADED.
Add to Cart
Stamping Auto Decoiler Straightener Feeder Non Metallic Stamping Processing Punch Feeder
In the stamping automation production process, the purchase of the punch feeder is mainly based on the characteristics of the stamping process, and the punching feed is selected according to the width, thickness, material and final product precision of the material to be punched. Machine equipment.
Therefore, the customer chooses the feeder should not be blind, you must first understand your needs, and then go to the targeted choice.
First of all, we must find out the material to be stamped. Whether the material is metal or non-metal, whether the material is soft or hard, whether it is easy to be scratched, and the metal material with higher hardness is the normal pull type punch feeder.
Basically all feeders can meet this requirement; soft materials, non-metallic materials, and easily scratched type materials require a special draw type feeder, that is, only air feeders or pneumatic NC feeders can be used.
Secondly, look at the brand and tonnage of the punching machine. If it is a high-speed punching machine, in order to ensure the production efficiency, the roller feeder, the clip feeder and the gear feeder should be selected. The roller feeder is mainly suitable for the production of 600 times/min or less and must be The press has an output shaft.
If the speed is exceeded, the other two should be selected. The gear feeder is mainly suitable for the double-head material frame, the S-type leveling machine, the stamping motor and the fixed rotor are special type, and the clip type feeder is the most mainstream feeding device for high-speed stamping.
Again, look at the thickness, width, and feed step requirements. If the material is above 3.5mm, only the NC feeder is suitable. If it is below 3.5mm, it needs to be combined with the material width and feed step.
Finally, it is clear whether the stamping process needs to be changed, whether it is often changed, if there is an NC feeder, it is the first choice. It has a multi-stage feeding setting and a touch screen point-controlled step setting. It is extremely convenient to install and use. Save customers the replacement step and mold change debugging time.
Products:
Specification:
| Model | MAC2-400 | MAC2-500 | MAC2-600 | MAC2-800 | ||
| Stock Width(mm) | 50-400 | 50-500 | 50-600 | 50-800 | ||
| Stock Thickness(mm) | 0.3~3.2 | 0.3-3.2 | 0.3-3.2 | -3.2 | ||
| Max.Coil Weight(kg) | 3000 | 3000 | 3000 | 5000 | 5000 | 7000 |
| Max.Coil O.D.(mm) | 1200 | 1200 | 1200 | |||
| Coil I.D.(mm) | 8 | 8 | 508 | 508 | ||
| Feed Length(mm) | ~500* | ~500* | ~500* | ~500* | ||
| Max. Line Speed(m/min) | 16-24 | 16-24 | 16-24 | 16-24 | ||
| Work Roll Number(pieces) | upper 6 lower 5 | upper 6 lower 5 | upper 6 lower 5 | upper 6 lower 5 | ||
| Feed Roll Number(set) | 1 | 1 | 1 | 1 | ||
| Main Motor(kw) | AC2.9 | AC2.9 | AC4.4 | AC4.4 | ||
| Mandrel Expansion | hydraulic | hydraulic | hydraulic | hydraulic | ||
| Reel Motor(kw) | 1.5 | 1.5 | 1.5 | 2.2 | 2.2 | 3.7 |
| Power(V) | 3 Phase 220V/380V/50HZ | |||||
| Operating Air(Mpa) | 0.49 | 0.49 | 0.49 | 0.49 | ||
Straigtening performance:
| tock Thicknees (mm) | Stock Width (mm) | |||
| 0.3 | 400 | 500 | 600 | 800 |
| 0.4 | ||||
| 0.6 | ||||
| 0.8 | ||||
| 1.0 | ||||
| 1.2 | ||||
| 1.4 | ||||
| 1.6 | 470 | 470 | ||
| 1.8 | 400 | 400 | ||
| 2.0 | 360 | 360 | ||
| 2.3 | 300 | 300 | 300 | 300 |
| 2.5 | 230 | 230 | 230 | 230 |
| 2.8 | 150 | 150 | 150 | 150 |
| 3.2 | 110 | 110 | 110 | 110 |
*1:(Pneumatic):Option in case of pneumatic mandrel expansion is provi