GUANGDONG RUIHUI INTELLIGENT TECHNOLOGY CO., LTD.
GUANGDONG RUIHUI INTELLIGENT TECHNOLOGY CO., LTD. AUTOMATION SOLUTIONS FOR ALL METAL FORMING STAMPINGS APPROACHING RUIHUI, NEW AUTOMATION TECHNOLOGY IS UPGRADED.
Add to Cart
Stamping and unwinding equipment, heavy material racks, peripheral stamping equipment
The heavy-duty material frame is the most used material discharging and unwinding equipment in stamping production. It controls the length of the material through the speed of the material frame controlled by the time relay, and automatically controls the length of the material through the height of the induction rod to realize and follow the whole process. Simultaneous processing of the flat machine, easy operation, large load capacity, high degree of automation, greatly improving the efficiency of stamping production.
Ruihui heavy-duty material frame consists of frame, reel, main shaft, adjusting device, sliding guide, back wheel, driving device and control box.
In actual use, the material frame handle is rotated counterclockwise, and the axial movement of the adjusting screw rod drives the four-bar linkage mechanism and the fan-shaped supporting material plate plate connected thereto, so that the diameter of the reel is reduced, the coil is loaded, and the clockwise rotation is performed. Material holder handle.
The material roll is tightened to complete the material feeding, the motor drives the winding tray to rotate and conveys the coil material, and the induction rod controls the opening and stopping of the material frame, and the time relay delay effect connected by the induction rod controls the discharging speed, and The material discharge length is controlled by the height of the sensing rod.
When the operator uses the heavy material frame for stamping production, it is not necessary to operate the machine frequently to control the material transportation, fully automatic operation, compact structure, small floor space, low failure rate, high work reliability, and effectively solve the stamping production. The problem of unloading and unwinding.
Products:
Specification:
| Model | MAC2-400 | MAC2-500 | MAC2-600 | MAC2-800 | ||
| Stock Width(mm) | 50-400 | 50-500 | 50-600 | 50-800 | ||
| Stock Thickness(mm) | 0.3~3.2 | 0.3-3.2 | 0.3-3.2 | -3.2 | ||
| Max.Coil Weight(kg) | 3000 | 3000 | 3000 | 5000 | 5000 | 7000 |
| Max.Coil O.D.(mm) | 1200 | 1200 | 1200 | |||
| Coil I.D.(mm) | 8 | 8 | 508 | 508 | ||
| Feed Length(mm) | ~500* | ~500* | ~500* | ~500* | ||
| Max. Line Speed(m/min) | 16-24 | 16-24 | 16-24 | 16-24 | ||
| Work Roll Number(pieces) | upper 6 lower 5 | upper 6 lower 5 | upper 6 lower 5 | upper 6 lower 5 | ||
| Feed Roll Number(set) | 1 | 1 | 1 | 1 | ||
| Main Motor(kw) | AC2.9 | AC2.9 | AC4.4 | AC4.4 | ||
| Mandrel Expansion | hydraulic | hydraulic | hydraulic | hydraulic | ||
| Reel Motor(kw) | 1.5 | 1.5 | 1.5 | 2.2 | 2.2 | 3.7 |
| Power(V) | 3 Phase 220V/380V/50HZ | |||||
| Operating Air(Mpa) | 0.49 | 0.49 | 0.49 | 0.49 | ||
Straigtening performance:
| tock Thicknees (mm) | Stock Width (mm) | |||
| 0.3 | 400 | 500 | 600 | 800 |
| 0.4 | ||||
| 0.6 | ||||
| 0.8 | ||||
| 1.0 | ||||
| 1.2 | ||||
| 1.4 | ||||
| 1.6 | 470 | 470 | ||
| 1.8 | 400 | 400 | ||
| 2.0 | 360 | 360 | ||
| 2.3 | 300 | 300 | 300 | 300 |
| 2.5 | 230 | 230 | 230 | 230 |
| 2.8 | 150 | 150 | 150 | 150 |
| 3.2 | 110 | 110 | 110 | 110 |
*1:(Pneumatic):Option in case of pneumatic mandrel expansion is provi