GUANGDONG RUIHUI INTELLIGENT TECHNOLOGY CO., LTD.
GUANGDONG RUIHUI INTELLIGENT TECHNOLOGY CO., LTD. AUTOMATION SOLUTIONS FOR ALL METAL FORMING STAMPINGS APPROACHING RUIHUI, NEW AUTOMATION TECHNOLOGY IS UPGRADED.
Add to Cart
Automated heavy material rack, unwinding leveling machine, metal sheet stamping
Under the work of the heavy-duty material frame power transmission mechanism, the main shaft is rotated, and the disc, the sliding sleeve and the sliding sleeve position adjusting mechanism are rotated, and the cantilever shaft is carried by the sliding sleeve, and then the cantilever shaft carries the coil material to complete the unwinding of the coil material. Feed and feed to the subsequent leveler or feeder.
When there is redundancy in the material to be delivered, the material will be sensed by the sensor frame due to falling, and the signal is fed back to the electrical control box by the sensor frame to temporarily stop the motor, and vice versa.
When the entire coil is used up, first remove the coil limit A-type iron, then operate the handle to shrink the cantilever shaft, and lap the other roll onto the tray, then connect the above operation can.
Therefore, during the whole process, the heavy material rack operator only needs to be responsible for placing the coil material on the tray and the corresponding operation of the handle and installing the coil limit A-type iron as needed, and once it enters the working state, it is fully automatic. The unwinding feed can save labor and reduce labor intensity, and can greatly improve the overall stamping efficiency.
At the same time, since the coil material is fastened to the tray of the cantilever shaft and protected by the A-type iron pipe, there is no swimming and swaying phenomenon, and the unwinding feeding effect of the coil material is ensured.
Products:
Specification:
| Model | MAC2-400 | MAC2-500 | MAC2-600 | MAC2-800 | ||
| Stock Width(mm) | 50-400 | 50-500 | 50-600 | 50-800 | ||
| Stock Thickness(mm) | 0.3~3.2 | 0.3-3.2 | 0.3-3.2 | -3.2 | ||
| Max.Coil Weight(kg) | 3000 | 3000 | 3000 | 5000 | 5000 | 7000 |
| Max.Coil O.D.(mm) | 1200 | 1200 | 1200 | |||
| Coil I.D.(mm) | 8 | 8 | 508 | 508 | ||
| Feed Length(mm) | ~500* | ~500* | ~500* | ~500* | ||
| Max. Line Speed(m/min) | 16-24 | 16-24 | 16-24 | 16-24 | ||
| Work Roll Number(pieces) | upper 6 lower 5 | upper 6 lower 5 | upper 6 lower 5 | upper 6 lower 5 | ||
| Feed Roll Number(set) | 1 | 1 | 1 | 1 | ||
| Main Motor(kw) | AC2.9 | AC2.9 | AC4.4 | AC4.4 | ||
| Mandrel Expansion | hydraulic | hydraulic | hydraulic | hydraulic | ||
| Reel Motor(kw) | 1.5 | 1.5 | 1.5 | 2.2 | 2.2 | 3.7 |
| Power(V) | 3 Phase 220V/380V/50HZ | |||||
| Operating Air(Mpa) | 0.49 | 0.49 | 0.49 | 0.49 | ||
Straigtening performance:
| tock Thicknees (mm) | Stock Width (mm) | |||
| 0.3 | 400 | 500 | 600 | 800 |
| 0.4 | ||||
| 0.6 | ||||
| 0.8 | ||||
| 1.0 | ||||
| 1.2 | ||||
| 1.4 | ||||
| 1.6 | 470 | 470 | ||
| 1.8 | 400 | 400 | ||
| 2.0 | 360 | 360 | ||
| 2.3 | 300 | 300 | 300 | 300 |
| 2.5 | 230 | 230 | 230 | 230 |
| 2.8 | 150 | 150 | 150 | 150 |
| 3.2 | 110 | 110 | 110 | 110 |
*1:(Pneumatic):Option in case of pneumatic mandrel expansion is provi